Have you got the broken laptop power jack? No worries, we have got you. We will figure out the ways to fix the broken power jack of your laptop. Because of their mobility,  notebooks are particularly vulnerable to environmental variables. We show you six innovative techniques to fix your laptop quickly and easily on your own or with the help of others. How to solder or not solder the laptop power jack. It can be difficult to repair a laptop’s power socket in particular.

Your mobile PC will ultimately have “experiences” with falls, bad luck, and worse, no matter how hard you try. However, any laptop issue should not be rushed to a PC repair agency or the manufacturer. You can also repair them yourself because it can cure various laptop problems for a lower cost and in a shorter length of time.

You’ll only need a few common tools, spare components, and some elbow grease. Some of these fixes are no more difficult than a seventh-grade art project.

However, there are already a number of modern laptops and notebooks on the market that are difficult to repair and hard to open. It’s possible that you’ll fail this project if there are no screws visible.

You should do your homework when it comes to finding the necessary spare parts, especially for power adapters or fans. While they may appear to be identical, their service may differ significantly.

YOU SHOULD CHECK A FEW THINGS TO KNOW IF YOUR JACK FAILED OR NOT

THE POWER LIGHT TURNS ON AND OFF

A properly functioning DC power jack can give your laptop with a constant flow of electricity. If your laptop’s power flickers or you have to wiggle your chord in the socket to keep it connected, there’s a problem with the jack. It’s a dangerous situation, and electricity sparks are nearly certain to happen.

IF YOUR BATTERY IS NOT CHARGING, THERE’S A PROBLEM

Even if your power cord or laptop does not show the symptoms listed above, the DC jack could be destroyed if your battery is not charging. You’ll need a stable electrical supply to set your laptop battery and give it a boost in charge. Failure to charge the batteries indicates that the DC power is not being converted properly.

JUST WORKS AT A CERTAIN ANGLE OR IN A SPECIFIC LOCATION

It’s an early warning indication that something bad is about to happen. When a DC power jack on your laptop loosens, it can no longer fit properly or move. As a result, you may need to angle your power cord to charge your device. It will put a strain on your power cable and DC jack, possibly resulting in damage to both.

HOW TO FIX LAPTOP POWER JACK WITH/WITHOUT SOLDERING?

NEEDED TOOLS AND SUPPLIES

An AC adaptor that is compatible with your laptop;

1. Sharpie or highlighter barrels are both empty.

2. Electrical connection tapes

3. To keep everything together, zip links were used.

4. Multimeter and Pliers

5. Soldering iron and solder

6. Wire strippers and other tools (for the AC on the laptop)

Boring holes can be done with screws, a screwdriver with nails, drills, and a hammer (or any other tool to make holes and can hold the barrel in position)

PROCEDURES

  • A barrel with two holes must be prepared first. Remove the ink holder portion and the marker’s tip to do so.
  • Make a hole on the opposite side of the marker barrel, and that’s all there is to it.
  • Preparing the cables is the next move. It entails severing the laptop cable. We’re dealing with two types of AC adapters in this case: a generic AC adapter and a laptop AC adapter. AC Adapter (Generic)
  • Cut the cord from the generic adapter to the length required. You want to make sure the cord isn’t too short or too long.
  • Attach the cord you prepared earlier into the barrel.
  • You will need to strip the wires to reveal them.
  • AC Adapter for Laptop
  • Reduce the size of the cord that needs to be replaced by cutting it.

In the tip of the marker barrel, insert the cable. (By removing the wires, make sure they’re exposed.)

To repair the power jack, connect the two cords together. It’s an important move, and you’ll need to keep your eyes peeled for any openings. Using a multimeter to double-check that you’re working with the right wires.

Double-check that the barrel has sealed after you’ve accomplished the preceding steps. If the wires have torn apart, zip ties may be used to keep them connected. The zip ties prevent the cords from being unplugged from the power outlet.

HOW LAPTOP POWER JACK WORK WITH CHARGER?

The most common laptop chargers employ two signals: +VE and GND. However, some manufacturers, like as Dell, add an extra sensing pin as well as positive and negative connectors to the laptop jack, resulting in three connections.

The cables from these DC-in jacks have been soldered together using a motherboard connection. In this instance, there are a few solutions for replacing the laptop power jack without soldering. Look at the photo of the dc jack below, which has been soldered directly to the motherboard, and you can’t do it without soldering.

HOW TO FIX LAPTOP POWER JACK WITH/WITHOUT SOLDERING (PROBLEMS RELATED TO PHYSICAL DAMAGE)

When a pin or the entire jack on your laptop breaks, there’s no way to fix it; you’ll have to replace it. Some people may suggest gluing it or doing something else, but I do not advise it.

Heat is generated when a poor connection between the dc jack and the adapter pin prevents a consistent current flow. It’s best to replace it because it can harm the laptop charging pin or possibly the motherboard if it’s used for a long period.

EASY AND DIRECT WAYS TO FIX LAPTOP POWER JACK WITH/WITHOUT SOLDERING

Take your time opening your laptop because there is always a little screw where you least expect it. Please make certain that the screws are ordered properly. Look for the laptop power socket if you’ve opened the laptop to fix it. Look at it once you’ve located it to see how it’s doing. There are two main scenarios.

First, all you have to do is reconnect the power jack to the laptop motherboard with a soldering iron (laptop repair pros have one, or you can acquire one from a hardware shop) and add a little solder to the legs to patch the loose link, and you’re done.

Second, repairing a laptop takes a long time since it requires a great deal of effort and knowledge, as well as the use of specialized equipment. It must first remove the motherboard’s damaged power jack.

Make sure you have the necessary parts before removing the broken power jack. Please double-check that you order the correct power jack; finding it will take time, and you won’t be able to reassemble your laptop while you wait.

When you get the part, carefully align the legs of the power jack with the motherboard floor and solder the power jack with a soldering iron, being cautious not to link the pins of the power jack. Please only attempt this if you have prior laptop repair experience or skill; otherwise, leave it to the pros.

You should put it back together and seal it up once you’ve completed soldering. Finally, turn on your laptop and plug in the power adapter to see whether it works. If the charging icon displays, you’ve done everything correctly and the laptop power jack is now fixed.

Video:

FAQS

IS IT POSSIBLE TO REPAIR A LAPTOP CHARGING PORT?

To fix the laptop charging port, you must first figure out what’s causing the problem. If the power jack is attached to the motherboard, you can readily detach and install it. If, on the other hand, the power jack damages the motherboard, you’ll have to deliver it and replace it.

IS IT POSSIBLE TO CHARGE MY LAPTOP USING ANY AVAILABLE CHARGER?

The laptop or the adapter would be harmed. If the adapter’s power rating is lower than that of the computer, the adapter’s power may increase abruptly rather than gradually as the computer’s load grows.

If the charger is rated higher, it may burn out the laptop’s circuit. In most cases, you won’t find chargers with the same pin size and various scores, but you won’t find them without them either.

WHAT IS THE BEST WAY TO SOLDER THE DC POWER JACK?

The procedure of connecting the DC jack directly to the motherboard is more convenient than removing it. Insert the DC jack into a pinhole on the motherboard and secure it with flux. Solder each of the pins to the motherboard attachment one by one with hot solder wire.

Leave a Reply

Your email address will not be published. Required fields are marked *